Contractors Save Money with Climate-Controlled Self Storage
The True Purpose of Air Filters in your HVAC System

Tips and Tricks for Drywall Plastering

5544468856_21cd157560_o

Hanging drywall is often a more forgiving tradesman’s job that doesn't necessarily require a high degree of precision and compliance with national and local standards. While there is no 100% way of hanging drywall, you still have to get it right, and there are countless ways to realize this.

By following the right techniques and with some repeatability, you can almost transform this into something of an art form, according to Plasterer Central Coast. Every drywall installation tradie will develop their unique way of accomplishing this that will enable them to have smooth muddling, taping and finishing in drywall installations. Here are some simple tips, tricks and hacks that you can use to hang drywalls correctly.

Get the Layout Right

You’ve got to get the layout right to ensure the drywall is installed and aligned correctly and with the best workmanship. Using a pencil, mark the areas where you will place the vertical studs. This will make it easier for you when the drywall panels are being attached to the framing. Before you start hanging the drywall panels, complete the insulating work as well as the vapour barrier installations.

Ensure the Framing is Flat

The drywall panels are likely to bend if the plane of the ceiling or the wall isn’t flat. It should be perfectly flat from stud to stud or between the ceiling joists. The bending of the panels creates ugly contours or even cracks on the finished ceiling or finished walls. That is why you should use level or straightedge to determine if the wall or the ceiling members are levels, flat and plumb. If it isn't level, you may need to plane down the framing members that shim out others extending farther out. For a perfect drywall installation, you need to get the plane’s level, flat and plumb.

Install the top row panels first

The professional way to install drywall panels is by starting from a single upper corner of the room and then installing the panels horizontally while ensuring the top edges are aligned against the ceiling. During the installations, the end of the panels must be placed at the centre of a stud. The panels may need to be scored and snapped into place to get the right fit.

User longer panels

DIYers tend to use 8-feet panels, but it is generally recommended that you use the 10 to 12 feet-long panels. These are also advantageous as they can cover the whole lengths of small rooms.

Start with the ceiling.

If you are drywalling an entire room, it is prudent to begin with the ceiling. The panels can be lifted and laid out against the ceiling joists with a pulley-driven drywall lift. Some crews use T-shaped “crutches” for placing the panels in place before driving in the nails or the screws. Overall, the techniques for installing the drywall panels onto the walls are mainly the same.

Attach the Panels to the Studs First

To hold the plasterboard securely against the studs, start by driving some nails and screws on their ends and down towards the centre. You should drive the screws far enough that they should ‘dimple’ the drywall surface, but they shouldn't go too deep that they'd break the paper surface. The strength of the attachment is undermined if the paper is broken. Drywall guns feature adjustable clutches that give you some control over the depth of the screw bit. Ensure that you choose the right size of screws and nails that will match the drywall size. The screws should be placed at least ½ inch from the edge of the panel.

The Panels Can Be Cut by Snapping

According to a professional plasterer, one of the easiest ways to cut the drywall length-wise is by first scoring a single side of the board using a utility knife. You can subsequently turn to the backside of the panel and crack it using your knee. If the gyprock board is hit at the correct spot, it will smoothly separate uniformly along the line you scored earlier. Once you have folded the panel along its scored line, you can slice it down straight along the fold on the other side using a utility knife. This will finish the cut.

Use the Right Tools

The secret to flawless drywall installations is using the right sets of tools, particularly those that are preferred by professionals. Having straight sets of tools is especially important if you will be installing the drywall alone. If you can’t afford the tools, you can rent them at the leading tool lease outlets or home improvement centres.

Some of the top tools that you should use for drywall installations include:

  • Drywall screwgun
  • Drywall stilts
  • Hydraulic drywall lift
  • Drywall rotary saw

partnered post • cc-licensed image by TrickyKid

Comments